Thanks Udo and Grant,
I have flashed de rpi again, the problem still exists. When ik click on list audio devices in de admin page, there is nothing. I will lookin it further. Bw and good holydays!

Wijnand



Verzonden vanaf mijn Galaxy


-------- Oorspronkelijk bericht --------
Van: Grant Smith <grant@soundtent.org>
Datum: 22-12-2021 13:02 (GMT+01:00)
Aan: locustream@locusonus.org
Onderwerp: Re: [locustream mailing list] raspberry pi zero with iqaudio hat

Thanks Udo
I guess, if the IQaudio card is visible in that list (ie it's not a hardware issue), then it could be worth re-flashing the disk image (which is pretty quick), in case that resolves it

bw all
grant


> On 21 Dec 2021, at 09:29, udo noll <un@aporee.org> wrote:
>
>
> can't help with the streambox image, but in order to see whether the IQAUDIO is
> there and ready, type:
>
> arecord -l
>
> should give you something like
>
> **** List of CAPTURE Hardware Devices ****
> card 0: IQaudIOCODEC [IQaudIOCODEC], device 0: IQaudIO CODEC HiFi v1.2 da7213-hifi-0 [IQaudIO CODEC HiFi v1.2 da7213-hifi-0]
>  Subdevices: 0/1
>  Subdevice #0: subdevice #0
>
> if no IQAudio appears here, something's wrong with it.
>
> u.
>
>
>
>
> Wijnand Bredewold:
>> Dear friends,
>>
>> I need some help. My streambox (RPI zero) dont recognize the iqaudio hat anymore.
>> Does somebody how to solve this? (or is the pi or the soundcard malfunction)
>> I can't choose under soundcard:
>>
>> My settings in streambox.txt:
>> # ---------------------------------------------------------------------------------------------------------------------
>> # ADVANCED AUDIO CONFIGURATION
>> # ---------------------------------------------------------------------------------------------------------------------
>> # IQaudIO audio card settings.
>> #
>> # - IQAUDIO_INPUT, select one input below (default "mems") :
>> #
>> # - mems to record from the on board digital MEMS microphone
>> # - mic to record from the mono/stereo mic input (electret)
>> # - aux to record from the stereo aux input
>> IQAUDIO_INPUT="mems"
>> # - IQAUDIO_MEMS_GAIN, MEMS input gain : min=-6.00dB max=36.00dB (default 24)
>> # - IQAUDIO_MIC_L_GAIN, mic input gain (left) : min=-6.00dB max=36.00dB (default 24)
>> # - IQAUDIO_MIC_R_GAIN, mic input gain (right) : min=-6.00dB max=36.00dB (default 24)
>> # - IQAUDIO_AUX_GAIN, stereo aux input gain : min=-54.00dB max=15.00dB (default 0)
>> # - IQAUDIO_MIX_PGA, mixin PGA (programmable-gain amplifier) : min=-4.50dB max=18.00dB (default 6)
>> # - IQAUDIO_ADC_GAIN, ADC (Analogue to Digital Convertor) : min=-78.00dB max=11.25dB (default 0 for aux, 1.5 otherwise)
>> IQAUDIO_MEMS_GAIN="24"
>> IQAUDIO_MIC_L_GAIN="24"
>> IQAUDIO_MIC_R_GAIN="24"
>> IQAUDIO_AUX_GAIN="0"
>> IQAUDIO_MIX_PGA="6"
>> IQAUDIO_ADC_GAIN="1.5"
>>
>> # Cirrus Logic/Wolfson audio card settings.
>> # Please note: only one input can be used for recording.
>> #
>> # - CIRRUS_INPUT, select one input below (default "mems") :
>> #
>> # - mems to record from the on board digital MEMS microphones
>> # - mic to record from the mic (or headset)
>> # - linein to record from the line input
>> # - micbias to record from the line input + bias voltage
>> # - spdifin to record from the S/PDIF receiver
>> CIRRUS_INPUT="mems"
>> # - CIRRUS_INL_VOL, audio interface volume (left) : min=-32.00dB max=16.00dB (default 0)
>> # - CIRRUS_INR_VOL, audio interface volume (right) : min=-32.00dB max=16.00dB (default 0)
>> # - CIRRUS_INL_PGA, programmable-gain amplifier (left) : min=0.00dB max=31.00dB (default 0)
>> # - CIRRUS_INR_PGA, programmable-gain amplifier (right) : min=0.00dB max=31.00dB (default 0)
>> # - CIRRUS_INL_DIG, digital input gain (left) : min=-64.00dB max=31.50dB (default -6 for mems, 0 otherwise)
>> # - CIRRUS_INR_DIG, digital input gain (right) : min=-64.00dB max=31.50dB (default -6 for mems, 0 otherwise)
>> CIRRUS_INL_VOL="0"
>> CIRRUS_INR_VOL="0"
>> CIRRUS_INL_PGA="0"
>> CIRRUS_INR_PGA="0"
>> CIRRUS_INL_DIG="-6"
>> CIRRUS_INR_DIG="-6"
>> # - CIRRUS_HEADPHONE, turn on/off playback to the headphone output (default "yes").
>> # - CIRRUS_LINE_OUT, turn on/off playback to the line output (default "yes").
>> # - CIRRUS_SPEAKER, turn on/off playback to the speakers output (default "no").
>> # - CIRRUS_SPDIF_OUT, turn on/off playback to the S/PDIF transmitter (default "no").
>> CIRRUS_HEADPHONE="yes"
>> CIRRUS_LINE_OUT="yes"
>> CIRRUS_SPEAKER="no"
>> CIRRUS_SPDIF_OUT="no"
>>
>> # Blue Icicle audio card settings.
>> #
>> # - BLUEICICLE_IN_GAIN, input gain: min=-8.00dB, max=14.00dB (default 0)
>> BLUEICICLE_IN_GAIN="0"
>>
>> I hope i to see some tips!
>>
>> Regards,
>> Wijnand
>>
>>
>
>> _______________________________________________
>> Locustream / Locus Sonus Streaming Project http://locusonus.org/
>> To unsubscribe, send a message to locustream-request@nujus.net with unsubscribe in the subject
>> or follow instructions here https://nujus.net/cgi-bin/mailman/options/locustream
>> _______________________________________________
>
> _______________________________________________
> Locustream / Locus Sonus Streaming Project http://locusonus.org/
> To unsubscribe, send a message to locustream-request@nujus.net with unsubscribe in the subject
> or follow instructions here https://nujus.net/cgi-bin/mailman/options/locustream
> _______________________________________________

_______________________________________________
Locustream / Locus Sonus Streaming Project http://locusonus.org/
To unsubscribe, send a message to locustream-request@nujus.net with unsubscribe in the subject
or follow instructions here https://nujus.net/cgi-bin/mailman/options/locustream
_______________________________________________